The product contains both PNP- and NPN open collector outputs, in which a fixed current is switched proportionally to the air speed at the rate of 10 pulses per m/s.

A built-in self-regulated heater reduces the risk of glazing.

The heater is supplied separately, which makes it possible to control the heating.

The DWS-V-DAC13 is equipped with a specially designed protection mechanism, which protects the bearings and the electronic parts against dirt and humidity.

The body of the sensor is made of black PVC, and the rotor is produced in stainless steel.

Features

• Anemometer with opto-electronic detection

• Measuring range: 2 to 30 m/s

• PNP and NPN open collector outputs in the same unit

• Current source outputs

• 10 to 28 VDC supply voltage

• All inputs and outputs are protected against reverse polarity and transients

• High ESD protection

• Built-in heater

• Dust sealing

The post DWS-V-DAC13 Cup Anemometer appeared first on SCL System.

The product contain 4-20 mA output proportionally to the air speed. A built-in self-regulated heater reduces the risk of glazing.

The heater is supplied separately, which makes it possible to control the heating.

The DWS-V-AGP is equipped with a specially designed protection mechanism, which protects the bearings and the electronic parts against dirt and humidity.

The body of the sensor is made of black PVC, and the rotor is produced in stainless steel.

Features

• Anemometer with opto-electronic detection

• Measuring range: 2 to 50 m/s

• Output: 4-20 mA

• 18 to 28 VDC supply voltage

• All inputs and outputs are protected against reverse polarity and transients

• High ESD protection

• Built-in heater

• Dust sealing

The post DWS-V-AGP Cup Anemometer appeared first on SCL System.

The product contains both PNP- and NPN open collector outputs, in which a fixed current is switched according to the selected direction.

A built-in self-regulated heater reduces the risk of glazing. The heater is supplied separately, which makes it possible to control the heating.

The DWS-D-DAC13 is equipped with a specially designed protection mechanism, which protects the bearings and the electronic parts against dirt and humidity.

The body of the sensor is made of black PVC, and the rotor is produced in stainless steel.

Features

• Wind vane for relative wind direction

• Opto-electronic detection

• PNP- & NPN-open collector outputs in the same unit

• Indication of 0˚ and 90˚ intervals

• 10 to 28 VDC supply voltage

• All inputs and outputs are protected against reverse polarity and transients

• Built-in heater

• Dust sealing

The post Wind Vane appeared first on SCL System.

The SMSAXP30 series is designed in conformity with EN ISO 12100:2010, EN 60204-1 and EN 1088. It is characterised by multiple flux coding and is suited for applications up to safety Category 3, in accordance with EN ISO13849-1:2015 when connected to appropriate safety devices.

Features

• Suitable for applications in safety category 3 in accordance with EN ISO13849-1:2015 when connected to appropriate safety devices

• 2 NO outputs

• Cable output connection

• Cylindrical housing

• Multiple flux coding

• In compliance with CEI EN 60947-5-3:2000

The post Cylindrical Safety Magnetic Sensor (2NO Outputs) appeared first on SCL System.

A family of metal face inductive proximity switches in industrial standard stainless steel housings (M8, M12, M18 and M30 types).

Output indication: by yellow LED. Outputs are open collector NPN or PNP transistors. Available with cable and M8 or M12 plug.

These sensors stand up to abrasion and impact caused by flying metal chips, grit and misaligned or vibrating targets.

In addition, the stainless steel body resists against corrosion and chemical attack, by offering a higher level of protection for more reliable operation and longer life in harsh environments.

Features

• Sensing distance: 1 to 15 mm

• Flush and non-flush types

• Long and short housing

• Rated operational voltage: 10 – 30 VDC

• Output: DC 100 mA, NPN or PNP

• Normally open, Normally closed

• Output indication: by yellow LED

• Protection: reverse polarity, short circuit, transients

• Cable and plug versions

The post IA30 Metal Face Inductive Sensor appeared first on SCL System.

A family of metal face inductive proximity switches in industrial standard stainless steel housings (M8, M12, M18 and M30 types).

Output indication: by yellow LED. Outputs are open collector NPN or PNP transistors. Available with cable and M8 or M12 plug.

These sensors stand up to abrasion and impact caused by flying metal chips, grit and misaligned or vibrating targets.

In addition, the stainless steel body resists against corrosion and chemical attack, by offering a higher level of protection for more reliable operation and longer life in harsh environments.

Features

• Sensing distance: 1 to 15 mm

• Flush and non-flush types

• Long and short housing

• Rated operational voltage: 10 – 30 VDC

• Output: DC 100 mA, NPN or PNP

• Normally open, Normally closed

• Output indication: by yellow LED

• Protection: reverse polarity, short circuit, transients

• Cable and plug versions

The post IA18 Metal Face Inductive Sensor appeared first on SCL System.

A family of metal face inductive proximity switches in industrial standard stainless steel housings (M8, M12, M18 and M30 types).

Output indication: by yellow LED. Outputs are open collector NPN or PNP transistors. Available with cable and M8 or M12 plug.

These sensors stand up to abrasion and impact caused by flying metal chips, grit and misaligned or vibrating targets.

In addition, the stainless steel body resists against corrosion and chemical attack, by offering a higher level of protection for more reliable operation and longer life in harsh environments.

Features

• Sensing distance: 1 to 15 mm

• Flush and non-flush types

• Long and short housing

• Rated operational voltage: 10 – 30 VDC

• Output: DC 100 mA, NPN or PNP

• Normally open, Normally closed

• Output indication: by yellow LED

• Protection: reverse polarity, short circuit, transients

• Cable and plug versions

The post IA12 Metal Face Inductive Sensor appeared first on SCL System.

Automatic frequency tuning and easy sensitivity adjustment enable easy setup and installation.

Automatic sensitivity boost ensures high bed vehicles are detected reliably.

Multicolor LED indication enables user to easily adjust loop inductance and intuitively indicate installation issues for easy diagnostic.

Individually user-assigned relay mode for 2 x SPDT outputs enables easy adaptation to many applications.

Directional logic in dual loop model can be used to ascertain vehicle direction.

Features

• Loop input inductance: 20 μH to 1000 μH

• Adjustable sensitivity in 10 steps: 0.01% to 1.00% via potentiometer

• Automatic loop frequency tuning or manual tuning via 4 adjustable loop frequency channels to avoid crosstalk

• Automatic Sensitivity Boost (ASB) for high bed vehicle detection

• Selectable fail safe and fail secure mode

• 2 x SPDT relay outputs, selectable operation as pulse or presence switching

• Multicolor power/fault LED indication for easy setup and intuitive diagnostic

• Individual loop state multicolor LED to indicate different loop status and fault.

• Loop diagnostic capability: loop short circuit, loop open circuit, inductance out of range, channel crosstalk.

• Directional logic for dual loop.

• Wide range power supply: 24-240 VAC/VDC, 45-65 Hz

Functions

• Opening and closing of barriers in a carpark. Output from loop detector can also be used to activate ticket machine and occupancy counting.

• Activation of bollards on the streets and any premise entrances/exits.

• Detecting vehicles at traffic light, tolls gantry and others.

• Directional logic to determine vehicle direction.

• Automatic Sensitivity Boost (ASB) function to detect high bed vehicles on the roads or in factories.

• Lighting activation in the car porch, carpark ramps and others.

The post Loop Detector (Plug-In Housing) appeared first on SCL System.

Automatic frequency tuning and easy sensitivity adjustment enable easy setup and installation.

Automatic sensitivity boost ensures high bed vehicles are detected reliably.

Multicolor LED indication enables user to easily adjust loop inductance and intuitively indicate installation issues for easy diagnostic.

Individually user-assigned relay mode for 2 x SPDT outputs enables easy adaptation to many applications.

Directional logic in dual loop model can be used to ascertain vehicle direction.

Features

• Loop input inductance: 20 μH to 1000 μH

• Adjustable sensitivity in 10 steps: 0.01% to 1.00% via potentiometer

• Automatic loop frequency tuning or manual tuning via 4 adjustable loop frequency channels to avoid crosstalk

• Automatic Sensitivity Boost (ASB) for high bed vehicle detection

• Selectable fail safe and fail secure mode

• 2 x SPDT relay outputs, selectable operation as pulse or presence switching

• Multicolor power/fault LED indication for easy setup and intuitive diagnostic

• Individual loop state multicolor LED to indicate different loop status and fault.

• Loop diagnostic capability: loop short circuit, loop open circuit, inductance out of range, channel crosstalk.

• Directional logic for dual loop.

• Wide range power supply: 24-240 VAC/VDC, 45-65 Hz

Functions

• Opening and closing of barriers in a carpark. Output from loop detector can also be used to activate ticket machine and occupancy counting.

• Activation of bollards on the streets and any premise entrances/exits.

• Detecting vehicles at traffic light, tolls gantry and others.

• Directional logic to determine vehicle direction.

• Automatic Sensitivity Boost (ASB) function to detect high bed vehicles on the roads or in factories.

• Lighting activation in the car porch, carpark ramps and others

The post Loop Detector (DIN Rail Housing) appeared first on SCL System.

Inductive proximity sensor with NAMUR output in M12 housing for flush mounting. Connection with 2 m silicone cable.

Features

• Nickel-plated brass housing

• Sensing distance: 2 mm

• Flush type

• Short body version

• Power supply: 8 VDC

• Output: NAMUR

• 2 m silicone cable

The post High Temperature Inductive Sensor with Namur Output appeared first on SCL System.